All Construction Plans submitted for permitting are required to be designed to meet the provisions of the NC Residential Code. All structural information must comply with the provisions of the NC Residential Code. Structural elements not found in the NC Residential Code must be designed and plans bear the seal of a NC registered design professional.

This is a minimum plan review checklist; additional information may be added by the applicant or requested in the field by the Inspector to determine compliance. Permit holders remain responsible for meeting all code requirements regardless of whether a review item is listed. This minimum review checklist is intended to help prevent any major non-compliance issues from being built in the field, which typically results in significant costs and delays on a project. Show all applicable information below to clearly describe scope of work, not all items are required. Alterations only, no new footprint for this permit type.

General

• Name, address, phone number and email of the person responsible for the design.
• If plans are stamped by a NC registered design professional, their seal is required to be signed and dated.
• Indicate if fire damage, storm damage, attic upfit, basement upfit, etc.
• Indicate proposed heated square footages, proposed unheated square footages (garage, porch, deck), existing heated and existing unheated square footages.
• If adding a bedroom, indicate number of proposed and number of existing, total number must match permit application and if applicable, septic system design.
• Energy code requirements: insulation, floors, walls and ceilings.
• Plans must be drawn to scale, legible, with sufficient clarity and detail to indicate the nature of the work, include Bar Scale.
• Designate a space on the plans for the reviewer's stamp.

Floor Plans

• Rooms labeled as to their intended use, dimensioned, label all unheated/unfinished areas. Clearly show location of work to be done, showing any existing conditions to clarify.
• Room, hallway and stair dimensions.
• Show all plumbing fixtures.
• Window and door sizes and locations, Glazing U-Factor.
• Label and show all fireplaces, prefab or masonry.

Elevations

• Front, sides and rear elevations.
• Building height, mean roof height and story height.
• Roof pitches.

Foundation/Floor Framing

• Wall footing width and depth, reinforcement if required.
• Foundation wall type, size and reinforcement if required.
• Pier footing size width and depth, reinforcement if required.
• Pier sizes and solid cap.
• Slab footings and layouts for mono-slabs.
• Slab thickness and details, reinforcement if required.
• Anchor bolt details.
• Crawl space ventilation calculations or closed crawl space marked on plans.
• Crawl space access size and location.
• Girder size, number of members, species, grade and spans.
• Floor joist direction, size, on-center spacing, species, grade and spans.
• If using I-Joist, plans or layout will need to list manufacturer, series, size and on-center spacing.
• If using open web floor trusses, layout from manufacturer required.
• Openings in floors, headers and trimmers marked.
• Floor sheathing type and thickness.
• Engineered structural elements, design and sealed plans are required to be onsite at first inspection.

Wall & General Framing

• Wall stud size, on-center spacing, species and grade.
• Wall header size, number of members, species, grade and spans.
• Number of jack and king studs for each opening.
• Beam type or species/grade, size, number of members and span.
• Stud column size, number of members, species and grade for beams and point loads.
• Wall sheathing type and thickness.
• Wall bracing method used.
• Portal / narrow wall bracing detail, if required.
• Point loads marked with load path and blocking requirements.
• If brick veneer used, list lintel requirements.
• Engineered structural elements, design and sealed plans are required to be onsite at first inspection.

Roof Framing

• Roof rafter direction, size, on-center spacing, species, grade and spans.
• Roof tie down method and continuous load path.
• Collar ties and rafter ties size and spacing.
• Ridge board, hip and valley sizes.
• Ceiling joist direction, size, on-center spacing, species, grade and spans.
• Openings in ceilings or roof, headers and trimmers marked.
• Roof sheathing type and thickness.
• Roof vent calculations or marked as unvented.
• Attic access size and location.
• Engineered structural elements, design and sealed plans are required to be onsite at first inspection.

Decks and Porches must comply with the provisions of the NC Residential Code- Appendix M. Decks with post heights exceeding the requirement of NCRC- App M- Table-AM108.1, and Decks supporting Hot Tubs and Spas, must be designed by a NC registered design professional.

• Deck plans are to be drawn with a top view looking down showing a portion of the house, labeling rooms that are leading onto the deck. Show any other proposed structures within. (fireplace, kitchen area, etc.)
• Elevations to be drawn for clarity, dimension tallest height of deck floor from finish grade. For porches, show how roof attaches to house, roof pitch.
• Overall dimensions and width of stair.
• Footing size, width, depth, location, spacing.
• Decks with post heights exceeding the requirement of NCRC- App M- Table-AM108.1, and Decks supporting Hot Tubs and Spas, must be designed by a NC registered design professional.
• Post size- width, height from top of footing to bottom of girder, spacing.
• Girder size, species-grade, spans, number of members, attachment.
• Floor joist size, spacing, species-grade, spans, direction, attachment.
• Bracing details for free standing decks and decks attached to structures with a deck floor height of 4 feet or more.
• Deck-to-house band attachment details.
• Show cantilevers with spans from support.
• Guardrails are required for over 30” above-grade deck floors.
• Porch Post size- width, height, spacing.
• Header size, species-grade, spans, number of members, attachment.
• Ceiling joist size, spacing, species-grade, spans, direction, attachments.
• Roof rafter size, spacing, species-grade, spans, direction, attachments.
• Ridge size.
• Band attachment to the house for a shed roof.